You're better off with the Actiontec Adapters as they allow the selection of the D-High band and a user selectable Lowest Useable Frequency, which can be used to set the adapter frequencies above any existing MoCA network, thereby separating the two MoCa networks. Once final note, if you're running the Nextbox Whole Home PVR system, which uses a MoCa network to transmit data between the Nextboxes, or any other MoCA network, you're going to run into a potential problem with the adapter selected MoCA network controller. There is also the goCoax adapters are also in the same category, 1 Gb/s end to end, once again most likely due to the use of 1 Gb/s ports, but also claims to run 2.5 Gb/s throughout the network: The Actiontec ECB6250 MoCA 2.5 adapters stipulate 1 Gb/s end to end, most likely due to the use of 1 Gb/s ports, but, it also claims to run 2.5 Gb/s throughout the network: That would allow you to use the max data rates provided by the MoCA adapter set. In this case, the adapters should allow you to use the entire D-Band, running from 1125 to 1675 MHz edge to edge. If you don't have the Nextbox Whole Home PVR system running, that allows you to use any other MoCa adapter set as an end to end set or system. If you don't have the Nextbox Whole Home PVR system running, you can still use the modem as one of the adapters, but, you would still end up the modem using only the D-High band for MoCA operations. The datasheet for the Actiontec ECB6200 indicates data rates over 1 Gb/s, but, it doesn't provide an exact theoretical number. That loss of 100 mhz in the D-Low band will restrict the data rate as shown by 800 Mb/s thru his Actiontec adapter. That configuration is set to allow the Nextbox Whole Home PVR system to use the D-Low band which runs from 1125 to 1225 MHz edge to edge (100 MHz wide).Īs a result, if you choose to use the modem as one half of the adapter set, thereby only buying one adapter, you are accepting the restriction to use the D-High band, as determined by the modem's D-High band configuration. This is seen on page 9 of the MoCA 2.0/2.5 spec: Rogers configures the modems to use the D-High band which runs from 1350 to 1675 MHz edge to edge (325 Mhz wide). There are caveats that should be noted:ġ. It's repeatable.Īny CGNM-3552 supports MoCA 2.0, as does the CODA-4582. If I unplug the line they sync back up, plug in and they don't. I started plugging the other lines into the splitter and it turns out that as soon as I plug in the inbound line to the input of the splitter the two actiontec adapters lose sync. In the basement unplugged everything from the 6 way splitter except the adapter in the basement and the line running to the master bedroom. (now I know the line running to the master bedroom is good) Moved the adapter back to the master bedroom but in the basement used a barrel connector to just directly join the adapter in the basement with the line going to the master. In basement just used short co-ax cable to join the two adapters and plugged them in. In the master bedroom I then took the cable from the wall into the second actiontec adapter and plugged in the cable box to the adapter as well.Īt this point all tv's work fine but the moca adapters will not sync up (no co-ax light). Rogers Splitter output 2 -> Moca Filter -> Neoteck 6 way moca splitter (5-2500mhz) POE -> Some sort of Rogers barrel type filter -> Rogers Splitter input (5-1000mhz splitter) I have the following all wired up in the basement where the Rogers line comes in: Thought I would use moca adapters for my wireless access points (will have one on each floor) so went out and bought the following to play around with: It's a relatively new house and they are using satellite tv so I'm assuming it will be RG6 cabling throughout. So I'm moving to a new house that doesn't have cat5 cables run but does have co-ax to pretty much every room.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |